Stone Texture Paint

Reference Price:USD/㎡
Brand:SKK
Material No.:IR8L3C2Z
Supplier: CONTACT USCONTACT US
Material ID:
Add to Project
Material Consultation
Overview
Product Reports
Documents
Specifications
Product Model:MS-85_90
Country of Origin:Shanghai, China
Mold Resistance‌:Mold Resistant
Water Resistance:Waterproof
Color:
Gray Series
Indoor/Outdoor:Outdoor
Finish:Semi-gloss,Matte,Soft Gloss,Glossy
Flammability:Not tested yet
Brand Name:SKK
Series Name:Stone Texture Coating Series
Category:Paint/Real Stone Paint
Customizable:Yes
Overview
Structural Diagram
Structural DiagramMaterial Image
Case Diagram
Case DiagramMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial ImageMaterial Image

Details

SKK Stone Paint is a decorative coating that beautifully mimics the appearance of marble and granite. With natural hues and a realistic texture, it perfectly recreates a luxurious architectural look. Manufactured from natural stone processed by crushing, the aggregates undergo high-temperature calcination and acid washing, ensuring toughness, colorfastness, and excellent weather resistance and durability. When applied to exterior walls for a stone-like effect, it requires no steel framing support—unlike natural stone—and simplifies installation, significantly shortening construction time. Key Features of SKK Stone Paint: 1. Self-cleaning properties keep walls looking clean. 2. Protective performance: resistant to acid, alkali, UV rays, and washable. 3. Non-fading colors thanks to original natural stone aggregates. 4. Outstanding durability and weather resistance.

Attention

Application Guidelines and Conditions

I. Application Notes

1. Recommended tools for exterior application: airless sprayer, universal spray gun, short-nap roller, texture roller, paint sprayer.

2. Substrate absorption can vary, which may cause color inconsistencies. Always apply a sufficient amount of the specified primer and topcoat to ensure uniform coverage. Because the coating is thin, surface irregularities will show through; for the best finish, make sure the substrate is as smooth and even as possible.

3. Where possible, work continuously. If you must stop, plan the break at a natural joint or corner to avoid visible lap marks.

II. Weather and Climate Conditions

Temperature:
① Do not apply when the temperature is below 5°C (41°F), or when rain or snow is expected.
② When there's a large temperature swing between morning and evening, adjust the application schedule based on the surface temperature.
③ In winter, stop early enough to allow the coating to dry before nighttime temperatures drop too low.
④ Never apply onto a frosted or icy surface.

Wind:
Stop work if the wind speed exceeds 5 m/s (approx. 11 mph). Wind-blown dust and debris can contaminate the fresh coating before the protective topcoat is applied.

Rain:
If the applied material is not fully dry when rain hits, the film formation will be damaged. Monitor the weather closely before, during, and after application, and adjust the schedule accordingly.

Condensation and Dew:
Applying coating onto a surface with condensation will result in poor adhesion and reduce long-term durability.

Humidity:
High humidity slows down drying. As a general rule, pause work when relative humidity exceeds 80%.

III. Job Site Management

1. Before starting full-scale application, always do a test area to confirm the desired finish and color.

2. Allow sufficient drying time between coats so each layer cures properly.

3. If the coverage rate falls below the specified amount per unit area, the result may show through the substrate or appear uneven in color.

4. After finishing, inspect the work carefully while scaffolding or cradles are still in place; it is much harder to fix issues once access equipment is dismantled.

IV. Protection

Start protective measures immediately after finishing. Remove any drips or spatters from door frames, windows, and other adjacent surfaces promptly. During application, mask off areas that should not be coated with protective film or builder's paper.

V. Material Storage and Handling

1. Store in a cool, dry place away from direct sunlight and high temperatures (always keep the storage temperature above 5°C/41°F).

2. For solvent-based materials, take precautions against fire. In case of fire, use a dry powder extinguisher or sand; do not use water.